LiftMaster openers
Raised-panel steel
Carriage house
Modern flush
Full-view glass
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateLiftMaster Torsion Spring Replacement: The Boulder City Owner’s Guide
If your LiftMaster door won’t lift, jerks on the way up, or you heard a loud bang from the garage, the torsion spring likely broke. We replace LiftMaster torsion springs for Boulder City homeowners at a typical installed price of $180 – $340, and because torsion spring failures are a repair we answer around the clock, we can often get to a broken spring the same day. The flat price is quoted and agreed before the wrench comes out, and most jobs finish in a single visit.
Owners usually find out this part failed the same way. The door is up when it shouldn’t be, or it’s down and stays down. A neighbor hears the bang from across the street. You press the remote and get a half-inch of movement and a motor that sounds strained. On a LiftMaster, the opener often keeps humming and then gives up, which makes people think the opener is dead when the spring is the real problem. That’s the part that carries the door’s weight, and it’s why the brand name on the opener doesn’t change how a spring is measured or replaced.
Which LiftMaster Models This Applies To
Torsion springs are a door-and-track part, not an opener part, so this work applies to every LiftMaster opener and door you’re likely to have. LiftMaster’s opener lines – the chain-drive and belt-drive residential units, the jackshaft models that mount beside the door, and the wall-mount openers – all sit on the same kind of torsion assembly. The spring doesn’t know your opener’s model number. What matters is measuring the old spring correctly: inside diameter, wire gauge, and wound length. If a spring is missing or unreadable, we measure the door height and width, the drums, and the bar to size the right one.
LiftMaster publishes part references for its openers, but the springs themselves are matched to your door, not to the opener brand. That’s the gotcha owners trip over. Order the wrong inside diameter and the spring binds on the bar or fails early. Wire gauge off by one size and the door won’t balance. We measure on site rather than guess from a label, and we’re factory-familiar with LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor, so a mixed setup doesn’t slow the job down. Mainspring Garage Door Co. Boulder City is an independent service provider and is not affiliated with LiftMaster.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Signs Your LiftMaster Torsion Spring Replacement Is Failing
- A loud bang from the garage. That’s the spring letting go, usually while the door is down. You’ll often find a visible gap in the coil the next morning.
- The door rises a few inches and stops. A broken spring means the opener is trying to lift the full weight of the door. The opener’s safety sensor usually resists and the door drops back down.
- It’s heavy to lift by hand. A balanced door takes one hand. If yours feels like dead weight, the spring has lost tension or broken and needs attention before the opener burns out.
- Uneven or jerky travel. A partial failure or a worn spring makes the door lurch. On a LiftMaster, the opener may sense the drag and reverse.
- A visible gap or rust in the coil. The coils loosen, the bar looks off-center, or you see rust along the spring. LiftMaster doors in Boulder City sit through real heat and dry air, and those swing between seasons dry out the steel faster than in a milder climate.
Replacement Cost & What’s Included
LiftMaster torsion spring replacement in Boulder City runs $180 – $340 installed. The range comes down to door size, whether you have a single or double spring setup, the wire gauge needed, and whether the cables and drums need attention at the same time. We quote the flat price before any work starts, so there are no surprises on the bill. Parts and labor are stated together, not buried in a separate line. If the cables or drums are worn, we’ll tell you up front rather than after the door is apart. Every completed job is covered by our 90-Day Done Right Promise, in writing: if the work isn’t right, we come back.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
We’ll be straight with you. Torsion springs store a serious amount of energy. A spring under tension can cause a deep cut or worse if it lets go wrong, and this is not the part to learn on. We don’t hand out winding instructions, because that’s how people get hurt. What you can safely check is simple: look (don’t touch) for a visible gap in the coil, listen for the opener straining, and test the door by hand with the opener disconnected. If it’s heavy or the coil looks broken, stop and call us at (833) 605-8582. We’ll quote the price before we start and answer the phone with a live person, day or night.
FAQs
A torsion spring usually gives roughly 10,000 cycles, which is about seven to ten years of normal use, and the dry Nevada air and summer heat can shorten that. If your door cycles often and the spring is a decade old, it’s on borrowed time. Call us for a look before it goes.
No. A broken torsion spring can’t be welded or repaired and has to be replaced. There’s no safe way to bring a snapped coil back into service, and a patch would fail again. Replacement with the correctly measured spring is the honest answer.
Most torsion spring replacements are finished in about an hour once we’re on site, and because we bring the springs we need, we usually do it in a single visit. If the cables and drums are also worn, it takes a little longer and we’ll tell you before we start.
We measure the door and match the spring’s inside diameter, wire gauge, and length, then install a spring built for that door rather than an off-the-shelf guess. We’re factory-familiar with LiftMaster and Chamberlain, and we’ll fit a quality equivalent when it serves the job. Call (833) 605-8582 for a free estimate.
Get Your LiftMaster Spring Fixed Right
A broken spring is a door that won’t work and an opener taking a beating. If your LiftMaster door is stuck, heavy, or banging, we can help. We state the price up front, answer the phone with a live person 24/7, and stand behind the work for 90 days in writing. Current offers include $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a standing 5% discount for seniors and veterans. Call us at (833) 605-8582 for a free estimate.
Written by the team at Mainspring Garage Door Co. Boulder City, serving Boulder City and nearby areas.